Watlow Electric 945 Manuál s instrukcemi stáhnout pdf

-1-

Dear MIFCO Customer:

We would like to thank and congratulate you on the purchase of the McEnglevan

machine and accessories, and to share with you our confidence in the quality and reliability

of our equipment.

The enclosed Operating Manual and Warranty Registration Card are important to

both of us for two reasons:

l. Your Registration Card, with proper serial number, will be documented in

our files and your written warranty will be forwarded to you upon the receipt

of this card. Please complete and mail the return card now.

2. Proper instruction on the maintenance of your machine is very important.

Please read your instruction manual completely for best results and

maximum machine tool life.

Should you ever need service, it is available through the distributors, our factory

representatives or directly from the factory. It is the obligation of our franchised distributor

who sells you this equipment to conduct field service where possible. Please contact

your local distributor first and they will assist you in resolving any problems you may

encounter.

We take pride along with you in your purchase of this equipment. We will be

happy to assist you in any way possible to receive optimum results in its operation and

use.

Sincerely yours,

Matt Walter

CEO

1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1

-1-Dear MIFCO Customer:We would like to thank and congratulate you on the purchase of the McEnglevanmachine and accessories, and to share with you our

Strany 2

-10-(For special order units with the following controller.)Operation of the Watlow 945 High Limit InstrumentThis is intended as a quick reference gui

Strany 3

-11-(For special order units with the following controller.)OPERATION OF HONEYWELL UDC-2000 SERIES CONTROLLERSTHIS IS INTENDED ASAQUICK REFERENCE GUID

Strany 4

-12-(For special order units with the following controller.)OPERATION OF HONEYWELL UDC-3000 SERIES CONTROLLERSEntering a Single SetPointIn order to se

Strany 5

-13-(For special order units with the following controller.)OPERATION OF THE HONEYWELL UDC-2000 HIGH LIMITTHIS IS INTENDED AS A QUICK REFERENCE GUIDE

Strany 6

-14-RECORDING INSTRUMENTThe recording instrument is powered by a toggle switch located next to the instrument or, in some units,will be wired to come

Strany 7 - ATTENTION: READ ME FIRST!!!

-15-INSTRUMENTATION WITH AUDIBLE ALARMProgramming for Honeywell InstrumentsA sample program is entered into the instrument memory at the factory to de

Strany 8

-16-ATMOSPHERE CONTROL OPTIONControl of the furnace atmosphere has become increasingly critical to successful heat treating withprecise metallurgical

Strany 9

-17-DUI020 partsUpper chamber:402537 Upper door plug008174 Upper door plug cement402580 Upper door seal ring assembly402568 Upper door seal ( 4 pcs. p

Strany 10

-18-DU1020 parts cont.AT units only:004219 Dwyer flow meter004226 Dwyer low pressure switch003906 Red low pressure light004315 12" thermocouple-

Strany 11

-19-DU1224 partsUpper chamber:401592 Upper door plug008174 Upper door plug cement402770 Upper door seal ring assembly402779 Upper door seal (4 pcs. pe

Strany 12

-2-IndexModel No. and Electrical Specifications ... 3Furnace Installation and S

Strany 13

-20-DU 1224 parts cont.AT units only:004219 Dwyer flow meter004226 Dwyer low pressure switch003906 Red low pressure light004315 12" thermocouple

Strany 14 - RECORDING INSTRUMENT

-3-DO NOT REMOVE THIS PAGE This manual contains the Electrical Wiring schematic applicable to this particular equipment. Ifthere are any question

Strany 15

-4-Furnace Installation and Set-Up1. Cut all banding, remove shrink wrap and remove furnace from skid. Be sure to locate hearth plate inpacking materi

Strany 16 - ATMOSPHERE CONTROL OPTION

-5-New Furnace BREAK-IN Procedure• These instructions apply to the following MIFCO models: HTE46, HTE-88, HTE-1212, HTE-1414,HTE-2020, HTE-2424- These

Strany 17

-6-Electric Heat Treat Furnace Start-Up ProcedureMIFCO Heat Treat Furnaces are very easy to operate. They have been thoroughly tested andcalibrated at

Strany 18

-7-ATTENTION: READ ME FIRST!!!Watlow F4 TemperatureControllerProgramming the Control InstrumentFirst of all, the Watlow Control Instrument is pre-prog

Strany 19

-8-(For special order units with the following controller.)Watlow Series 96 Temperature ControllersThe HTE-46, E4-0, EM-46, and the EM-810 furnaces ar

Strany 20

-9-(For special order units with the following controller.)Operation of the Watlow 942 and 945 Control InstrumentThis is intended as a quick reference